Home/News/Choosing Slot Size on Oil Well Screens: From Formation Sand to Slot | ERQI WIRE
Choosing Slot Size on Oil Well Screens: From Formation Sand to Slot | ERQI WIRE
Slot size is a sand-retention decision made from a sieve analysis, not a catalogue pick. How D10/D50/D90 map to a slot, what changes when a gravel pack is involved, and where the field rules stop working.
Slot size is the one number on an oil well screen that the buyer gets to decide, and the one most often decided by habit. A well that got 0.3 mm on its last completion does not automatically want 0.3 mm again — the formation decides, and the formation says so through a sieve analysis. This article walks that path from sand sample to slot number, including where the shortcut rules break.
Start from the sand, not the catalogue
Representative sand means a sample that survived the trip: settle cuts, shake-outs or production solids caught downstream of a desander do not count. Run it through a sieve stack or a laser analyser and read three numbers: D10, D50 and D90 — the opening sizes that pass 10, 50 and 90 % of the grains by weight. The spread between them, D40/D90, is the uniformity coefficient, and it matters as much as the median: well-sorted sand (coefficient near 1) retains easily, poorly sorted sand (coefficient above 3) sifts through a slot sized for its median and blinding becomes a plug-formation race.
The field rules, stated honestly
For a screen doing direct retention — no gravel pack — the working rule is that the slot should hold back roughly 90 % of the formation sand, which puts the slot near D10, sometimes between D10 and D40 depending on how conservative the completion engineer is. On a typical medium-fine sand that lands the slot in the 0.15–0.30 mm band; coarser sands go to 0.35–0.50. These are rules of thumb refined over decades of completions, not physics — the physics is bridge formation at the slot mouth, and it depends on grain shape and drawdown as much as on the sieve curve. When the numbers sit near a boundary, the honest answer is a retention test on the actual sand, not a bigger safety factor.
| Situation | Working rule |
|---|---|
| Direct retention, well-sorted sand | Slot ≈ D10; verify against D40 that bridging is plausible |
| Direct retention, poorly sorted sand | Slot ≈ D10, and expect the screen to lean on the fines passing — if not, this is premium-screen territory |
| Gravel pack | Screen slot sized to hold the gravel (well below gravel D10), not the formation sand |
| Uniformity coefficient > 3 | Wire wrap alone may be insufficient; flag it to the completion engineer before quoting |
The gravel pack row is where copy-paste errors happen: sizing the screen slot as if it stopped formation sand directly produces slots so fine that gravel plugs them during placement. The screen and the gravel have to be designed as a pair — the gravel pack screens page carries the heavier-construction side of that.
Measure the slot where the sand sees it
A wedge slot is narrow at the outside face and widens inward. The number that governs sand retention is the outside gap, so that is where the gauge goes — slot checked per turn on the wound screen, held to +/-0.05 mm. A supplier who reports the wire height on a drawing instead of the measured outside gap is reporting a drawing, not a screen. The geometry behind this is the same for every wedge wire product and is explained in the slot calculation article.
Slot size is not the only retention decision
Finer slots retain more and plug sooner; coarser slots produce freely and pass sand until the formation bridges. The screen material decides how much of that trade you can afford: at depth and temperature the wrap is under load for decades, which is where duplex and C276 move from corrosion calls to mechanical ones, and the construction of the jacket is shared with our wire wrapped sand control screens.
Send the sieve curve — D10, D50, D90 and the uniformity coefficient — with the casing size, and the quotation will come back with the slot we would run ourselves and the reasoning behind it.
More from ERQI
-
Technical
Wire Wrapped Screens or Slotted Liners: Which One Does the Well Need? | ERQI WIRE
Slotted liners cost a fraction of wire wrapped screens and fail in specific, predictable ways. The four well conditions that decide between them, and what each failure actually looks like downhole.
-
Technical
809C and 202B: The High-Manganese Alloys Behind Wear Screens | ERQI WIRE
809C (10Cr21Mn16NiN) and 202B (12Cr18Mn8Ni5N) replace nickel with manganese and nitrogen. Why that makes them hard, non-magnetic and cheap, and where the trade stops working.
-
Technical
Wedge Wire Alloy Selection: Abrasion or Corrosion First? | ERQI WIRE
Seven alloys get quoted for wedge wire screens and they are not on one scale. Two questions decide almost every case: is there chloride, and is the duty abrasive. A working decision tree with the numbers behind it.
Ready to start your project?
Send us your drawing or sample — we reply within 24 hours on working days.