Home/News/Wedge Wire Screens or Woven Wire Mesh: Choosing the Screening Surface | ERQI WIRE
Wedge Wire Screens or Woven Wire Mesh: Choosing the Screening Surface | ERQI WIRE
Woven mesh costs less per square metre and wedge wire outlasts it by seasons. The real difference is the shape of the opening: one is a hole that plugs, the other is a slot that sheds. Where each surface wins, with the duties in between.
Woven wire mesh is the default screening surface almost everywhere, and for good reasons: it is cheap per square metre, available in every aperture from every stockist, and easy to replace. So a wedge wire screen has to argue its case against a product that is a fraction of its price — and the argument rests entirely on the shape of the opening.
A hole plugs; a slot sheds
A woven aperture is a hole through a crossed lattice: a particle that fits the hole can lodge in it from either side, and particles slightly larger bridge across the weaves and reduce the opening further. A wedge aperture is a slot between two tapered bars: narrow at the screening face, widening inward, so a particle that passes the face cannot lodge at its own size, and one that is stopped sits on the face where flow or vibration moves it off. Over hours of duty, that geometry difference compounds into the practical one: woven mesh blinds on sticky, flaky or near-size material; wedge wire keeps its open area.
Where the arithmetic favours wedge wire
- Near-size particles. Any duty where the feed is full of particles close to the cut point — sizing, classification, desliming — is exactly the condition that blinds woven cloth. The wedge slot shrugs at near-size.
- Backwashable surfaces. Wedge wire takes reverse flow without damage, so filters built from it — laterals, candles, screens — are cleaned in place. Woven cloth under backwash load sheds weave or stretches the aperture.
- Continuous duty. A wedge wire panel is welded stainless, wear measured in seasons; a cloth panel is held by clips and wear measured in shifts. On a duty that runs 24/7, the downtime to swap cloth costs more than the metal difference within a year.
- Support-free spans. Wedge wire needs no support grid underneath; woven cloth above roughly 1 mm aperture needs one, which costs open area and assembly.
Where woven mesh still wins — honestly
Below roughly 50 µm, wedge wire reaches its practical limit: the bar tops get fragile and the open area collapses, while woven mesh goes to 20 µm and beyond off the shelf. Cheap, sacrificial surfaces — scalping screens swapped hourly, one-shift filter bags — are woven's home ground, because a surface designed to be thrown away should not be made from welded stainless. And on duties with negligible blinding risk and short runs, the metal premium never pays back.
The middle ground, where most quotations live
Above 100 µm, with any real solids load, running continuously, the comparison resolves into cost per season rather than cost per square metre — and that is where wedge wire panels, flat screens, sieve bends and laterals take over from cloth. The same geometry underlies every product in the wedge wire range; the slot side of the arithmetic is in the slot calculation article, and the alloy side in the alloy decision tree.
Send the aperture, the material and the duty cycle, and we will say when the answer is woven mesh — it sometimes is, and the quote is cheaper for saying so.
More from ERQI
-
Technical
Why Sand Control Screens Fail: Five Field Failure Modes | ERQI WIRE
Screens rarely fail at random. Erosion at the slot edges, blinding from fines, dissimilar-metal corrosion, installation damage and a wrong slot size account for most downhole failures. What each one looks like when the screen comes back.
-
Technical
Wire Wrapped Screens or Slotted Liners: Which One Does the Well Need? | ERQI WIRE
Slotted liners cost a fraction of wire wrapped screens and fail in specific, predictable ways. The four well conditions that decide between them, and what each failure actually looks like downhole.
-
Technical
Choosing Slot Size on Oil Well Screens: From Formation Sand to Slot | ERQI WIRE
Slot size is a sand-retention decision made from a sieve analysis, not a catalogue pick. How D10/D50/D90 map to a slot, what changes when a gravel pack is involved, and where the field rules stop working.
Ready to start your project?
Send us your drawing or sample — we reply within 24 hours on working days.