Home/News/Wire Wrapped Screens or Slotted Liners: Which One Does the Well Need? | ERQI WIRE
Wire Wrapped Screens or Slotted Liners: Which One Does the Well Need? | ERQI WIRE
Slotted liners cost a fraction of wire wrapped screens and fail in specific, predictable ways. The four well conditions that decide between them, and what each failure actually looks like downhole.
Slotted liners are cheaper per metre — often a third of the price of a wire wrapped screen — and for some wells that is the correct economics, not a compromise. The failure modes of a slotted liner are specific and predictable, which means the choice can be made from four well conditions instead of from budget reflexes. This article sets out both sides the way a completion engineer would.
What each one actually is
A slotted liner is casing with straight slots milled or plasma-cut through the wall. The slot is a machined channel of constant width through the wall thickness — what a grain fits, it keeps fitting. A wire wrapped screen is triangular V-wire wound around a perforated base pipe and welded at every crossing: the slot is a wedge, narrow outside, wide inside, with no wall thickness behind it. The geometry difference drives everything below, and the wrap side is detailed on the wire wrapped screens page.
Four conditions decide it
| Condition | Favours slotted liner | Favours wire wrapped screen |
|---|---|---|
| Depth | Shallow wells, low differential | Deep wells — milled slots erode open under produced-sand traffic; a wrap keeps gauge for the life of the well |
| Sand | Coarse, well-sorted, low sand production expected | Fine or poorly sorted sand — slot precision matters, and the wedge shed geometry resists plugging |
| Well path | Vertical, short intervals | Deviated and horizontal — liners wear on the low side and milled slots there widen first; wrap is uniform around the circumference |
| Service life and workover cost | Short-life wells, cheap workovers | Offshore, thermal or high-rate wells where a screen failure means a rig |
The economics reverse when a failure is expensive. Onshore shallow wells get slotted liners because a squeeze or a re-completion is a pump-truck visit. Offshore, a sanding screen is a workover with a rig day-rate attached, and the wire wrapped screen premium is paid back by the first avoided intervention.
How the failures actually look
A slotted liner rarely fails by plugging first; it fails by erosion. Produced sand travelling through a milled slot abrades the cut edges, the slot widens, and the liner passes what it used to stop — sand production ramps gradually, which is precisely why operators miss the window. A wire wrapped screen fails the other way: its slot stays at gauge because the wear surface is a work-hardened drawn wire, and when it does plug, the wedge geometry lets a pulsed backwash clear what a constant-width channel cannot. Neither is fragile — they fail along different axes, and the well conditions above select which axis you can live with.
Where we land
When the four conditions point at a wrap, the remaining decisions — slot from the sand analysis, material from the water chemistry — follow the method in the slot size article and the alloy tree in abrasion or corrosion first. The same wedge physics at civilian pressures is covered in the water well comparison.
Send the well depth, deviation, sand analysis and expected rate, and we will say if a slotted liner is the right call — some wells genuinely want one, and saying so early is cheaper for everyone than finding out downhole.
More from ERQI
-
Technical
Choosing Slot Size on Oil Well Screens: From Formation Sand to Slot | ERQI WIRE
Slot size is a sand-retention decision made from a sieve analysis, not a catalogue pick. How D10/D50/D90 map to a slot, what changes when a gravel pack is involved, and where the field rules stop working.
-
Technical
809C and 202B: The High-Manganese Alloys Behind Wear Screens | ERQI WIRE
809C (10Cr21Mn16NiN) and 202B (12Cr18Mn8Ni5N) replace nickel with manganese and nitrogen. Why that makes them hard, non-magnetic and cheap, and where the trade stops working.
-
Technical
Wedge Wire Alloy Selection: Abrasion or Corrosion First? | ERQI WIRE
Seven alloys get quoted for wedge wire screens and they are not on one scale. Two questions decide almost every case: is there chloride, and is the duty abrasive. A working decision tree with the numbers behind it.
Ready to start your project?
Send us your drawing or sample — we reply within 24 hours on working days.