Home/Products/Wedge Wire/Wedge Wire Centrifuge Baskets
Wedge Wire Centrifuge Baskets
The screening surface inside a centrifuge, built to take the g-force: welded V-wire on a balanced basket, slots held along the full cone, segments replaceable where wear concentrates.
Wedge Wire Centrifuge Baskets
The screening surface inside a centrifuge, built to take the g-force: welded V-wire on a balanced basket, slots held along the full cone, segments replaceable where wear concentrates.
| Material | 304 / 316L / 2205 duplex; 202B and 809C for coal and abrasive crystal duty |
|---|---|
| Size range | OD 300-1500 mm, height to 1200 mm, slot 0.1-1.0 mm, cone half-angle 10-20 degrees, one-piece or segmented, reinforcing bands and balance record per basket |
| Typical application | Coal preparation screen-bowl and pusher centrifuges, sugar and salt dewatering, chemical crystal separation, starch and fibre recovery, mineral concentrate dewatering |
| Cross-section | Square — also drawn to your drawing |
| Surface | Bright drawn, as required |
| Packing | Coil, spool or straight length |
A centrifuge basket is the hardest duty a wedge wire surface takes. The same slot geometry that separates by gravity on a sieve bend now runs at 300 to 1500 g, with a cake sliding up a cone under its own weight and every bar top scraping abrasive solids at speed. The design problem is not the screening — it is holding slot size, roundness and balance while the surface wears.
What g-force changes
Under gravity, a screen needs enough open area to pass the liquor. Under centrifugal load, it needs structural continuity: the wire is not just a surface, it is a load path. Bars are welded to axial rods at every crossing, the rods land on reinforcing bands, and the bands transmit the load into the basket hub. Slot width and bar section are therefore chosen together with the rod schedule — a fine slot on a light schedule will deflect between bands and open under load, which shows up as product moisture creeping up over a campaign.
Cone angle and cake travel
The cone half-angle sets how fast the cake travels and how dry it leaves. Coal screen-bowl baskets commonly run 12–15 degrees; fine chemical crystals want a steeper cone so the cake does not stall. The angle is machined into the basket, so it is quoted with the basket, not adjusted later.
Segments where the wear is
Wear is never even around a basket. On coal duty the discharge end and the first band take most of the abrasion; on salt and sugar the whole surface sees uniform but lighter load. Larger baskets are built as replaceable segments — the worn band or segment is swapped without scrapping the hub, which is usually the difference between a basket that pays for itself and one that does not. Alloy choice follows the same logic as flat mining panels: 202B and 809C work-harden at the bar tops and outlast 304 several times in coal slurry, while chloride-bearing process liquors belong to 2205 duplex.
Balance is a delivered value
A basket that is out of balance shakes the whole machine, wears its bearings and shows up as vibration trend alarms long before the surface fails. Every basket ships with its balance record and its diameter checks at the top, middle and discharge bands. If the basket is a replacement, send the original drawing or the machine model — interchangeability matters more than any specification on this page.
Specifications
| OD | 300–1500 mm |
|---|---|
| Height | To 1200 mm; one-piece or segmented |
| Slot | 0.1–1.0 mm at the outside face |
| Cone half-angle | 10–20 degrees, machined to your machine |
| Bands / rods | Stainless, matched alloy, welded load path to the hub |
| Documents | Balance record, diameter checks, wire heat numbers, gauge report |
Baskets share their wrap and rod construction with our screen cylinders, and the wire itself is drawn on the triangular wire line. Send the machine model, basket drawing and duty, and the quotation will confirm the cone angle, segment split and alloy we would build for that wear pattern.
Related products
Ready to start your project?
Send us your drawing or sample — we reply within 24 hours on working days.