Home/News/How to Specify a Wedge Wire Screen: The Five Numbers That Matter | ERQI WIRE
How to Specify a Wedge Wire Screen: The Five Numbers That Matter | ERQI WIRE
A wedge wire screen quotation is a five-number conversation: slot width, wire profile, support rod, open area and material. What each number decides, how they trade against each other, and what a complete RFQ looks like.
Buying a wedge wire screen is mostly a five-number conversation. Send all five and the quotation comes back in days with real sizes and a tooling answer; leave one out and the reply turns into a question sheet that costs a week. These are the five, in the order they matter.
1. Slot width — what the screen actually separates
The slot is the gap between wire faces at the screening surface, measured across the outside. It decides the cut point, so it comes first: dewatering duty runs 0.25–1.0 mm, mineral sizing goes coarser, filter elements go down to 0.05 mm where the open area still justifies the metal. Below roughly 0.1 mm the bar tops get fragile and the open area collapses fast — if the process really needs finer than that, the honest answer is a different surface, not a heroic slot. For downhole sand control the slot is sized from sieve data rather than habit, which is its own article: choosing slot size on oil well screens.
2. Wire profile — the bar that forms the slot
The V-wire has a width and a height, and both matter. A wider bar carries more wear at the face and welds faster; a taller bar spans longer supports; both eat open area as they grow. Common sections run from 1.5 × 2.5 mm for fine filtration up to 3 × 5 mm for heavy mining duty, and the profile list is on the triangular wire page. The practical rule: pick the smallest bar that survives the duty, because every tenth of a millimetre of bar width is open area you paid for but do not get.
3. Support rod — the strength under the surface
Under the wrap wire sit support rods, and their size and spacing decide how much load the screen takes before the surface deflects. Standard spacing is 25–50 mm; a flat panel on a vibrating screen wants heavier rods and closer centres than a static filter element, and a well jacket wants a schedule that survives racking. Rod alloy is not a place to save money either — a noble wire welded to a lesser rod is a battery in brine, the failure mode described in the screen failure article. The bar stock itself is the support bar page.
4. Open area — the flow number
Open area is the percentage of the surface that actually passes flow, and it falls as slot narrows and bar widens — the three numbers trade against each other, which is why they should be quoted together. The arithmetic is worked through in the slot calculation article. One caution: a specification that asks for maximum open area is asking for a fragile screen. Size the flow from the process, keep the mechanical margin, and accept the open area that survives.
5. Material — how long it lasts
304 covers most fresh-water and neutral duty; 316L for chlorides; 2205 duplex where chloride and strength both bite; C276 for acid duty. The decision tree — abrasion or corrosion first — is in the alloy selection article. Match every wetted part, including the rods and the end rings, not just the wire.
What a complete RFQ looks like
| Slot width | 0.5 mm, at the outside face |
|---|---|
| Wire profile | 2 × 3 mm V-wire (or "your standard for this duty") |
| Support rods | 5 mm rod at 40 mm centres |
| Geometry | Flat panel 1500 × 1000 mm, wire across the flow |
| Material | All wetted parts 316L |
That RFQ quotes in one pass — no follow-up questions, no sample loop. Send yours in that shape, even rough, and the reply will include the trade-offs we would flag on each number rather than a bare price.
More from ERQI
-
Technical
Why Sand Control Screens Fail: Five Field Failure Modes | ERQI WIRE
Screens rarely fail at random. Erosion at the slot edges, blinding from fines, dissimilar-metal corrosion, installation damage and a wrong slot size account for most downhole failures. What each one looks like when the screen comes back.
-
Technical
Wedge Wire Screens or Woven Wire Mesh: Choosing the Screening Surface | ERQI WIRE
Woven mesh costs less per square metre and wedge wire outlasts it by seasons. The real difference is the shape of the opening: one is a hole that plugs, the other is a slot that sheds. Where each surface wins, with the duties in between.
-
Technical
Wire Wrapped Screens or Slotted Liners: Which One Does the Well Need? | ERQI WIRE
Slotted liners cost a fraction of wire wrapped screens and fail in specific, predictable ways. The four well conditions that decide between them, and what each failure actually looks like downhole.
Ready to start your project?
Send us your drawing or sample — we reply within 24 hours on working days.